Hot tub pump leaking?
A leaking pump is almost always a seal failure — most often a worn shaft seal, sometimes a union o-ring or the volute o-ring. It's usually a seal or wet-end repair, which is far cheaper than replacing the pump.
from $239 · $69 diagnostic credited to your repair
Water is escaping where a seal has given up
A puddle under the equipment bay almost always traces back to the pump, and almost always to a seal that has worn out. The pump is full of pressurized water whenever it runs, and several rubber and ceramic seals are all that keep that water inside the wet end and off the motor and floor. When one wears, you get a drip, a trickle, or a steady weep depending on where it failed.
The most common offender is the shaft seal — the spring-loaded seal where the spinning motor shaft enters the wet end. It takes the most wear, and as it degrades it lets water seep out around the shaft. The danger here isn't just the puddle: water that gets past the shaft seal heads straight for the bearings and motor, which is how an ignored leak becomes a far costlier bearing or winding failure.
The other two are static seals. A union o-ring at the threaded fittings where the plumbing meets the pump can dry out and leak, and so can the larger volute o-ring that seals the wet-end housing halves. These are often the easiest and cheapest of all to put right. Pinning down exactly which seal is weeping is the first job — and in every case it's a seal or wet-end repair, not the price of a new pump.
We'll confirm which for $69 — credited to the repair
Where the water shows points one way; we confirm on site.
Likely an o-ring if…
- The drip is right at a threaded union fitting
- It leaks only when the pump is running under pressure
- It started soon after the pump was opened or moved
- The water tracks from the housing seam, not the shaft
Likely the shaft seal if…
- Water weeps from where the shaft meets the wet end
- You've also heard a squeal at startup
- There's rust forming toward the motor side
- The leak has crept worse over weeks
Find the weeping seal, reseal the wet end, stop the leak
Trace the leak
We run the pump and pinpoint whether water is escaping at the shaft, a union, or the volute housing seam.
Flat quote
Once the failed seal is identified, you get the published price up front — the $69 diagnostic credited 100%.
Reseal
We rebuild the wet end with a fresh shaft seal and o-rings, or replace the specific union or volute o-ring that's weeping.
Verify
We run it under pressure and confirm the leak is gone and the bearings are dry before we leave.
Most pump-leak repairs are completed same-day across Palm Beach County.
A small pump leak doesn't stay small
Water that slips past the shaft seal runs toward the motor bearings and windings. A cheap seal repair today prevents a seized bearing or a shorted motor — and a motor short can trip your GFCI. If your pump is dripping, it's worth resealing before it reaches the electrical side.
Flat-rate, published up front
A seal or wet-end repair handles the great majority of pump leaks; a replacement pump applies only if a leak already wrecked the motor — confirmed at your $69 diagnostic.
Not quite your symptom?
Answers before you call
It's a seal failure. Most often the spring-loaded shaft seal where the motor shaft enters the wet end has worn out; sometimes it's a union o-ring at the fittings or the larger volute o-ring sealing the housing. We pinpoint which is weeping.
The great majority of pump leaks are fixed with a seal or wet-end repair — far cheaper than a new pump. A replacement is only needed if a long-ignored leak already damaged the bearings or motor.
Not for long. Water that gets past the shaft seal runs toward the motor bearings and windings, and a wet motor can short and trip your GFCI. It's best to reseal the pump before the leak reaches the electrical side.
From $239 for a seal or wet-end repair, which covers most leaks. A replacement pump applies only if the motor is already damaged. You get the flat price before we start.
Same-day across most of Palm Beach County, with a real arrival window rather than a vague all-day wait.
We'll reseal it before it kills the motor — today.
Flat-rate from $239. Same-day. $69 diagnostic credited to your repair.
Tell us where it's dripping — we'll call back within the hour
No call center. Just a local, licensed tech who'll find the failed seal and quote the price before any work.
Quote request sent
We'll call you back within the hour. Hot tub out cold right now? Call us at (561) 555-0143.